Intel

Cyclone® IV E Field Programmable Gate Array (FPGA) IC 532 1161216 39600 780-BGA

Operating Conditions

When Cyclone IV devices are implemented in a system, they are rated according to a

set of defined parameters. To maintain the highest possible performance and

reliability of Cyclone IV devices, you must consider the operating requirements

described in this chapter.

Cyclone IV devices are offered in commercial, industrial, extended industrial and,

automotive grades. Cyclone IV E devices offer –6 (fastest), –7, –8, –8L, and –9L speed

grades for commercial devices, –8L speed grades for industrial devices, and –7 speed

grade for extended industrial and automotive devices. Cyclone IV GX devices offer

–6 (fastest), –7, and –8 speed grades for commercial devices and –7 speed grade for

industrial devices.

Cyclone IV E devices are offered in core voltages of 1.0 and 1.2 V. Cyclone IV E

devices with a core voltage of 1.0 V have an ‘L’ prefix attached to the speed grade.

In this chapter, a prefix associated with the operating temperature range is attached to

the speed grades; commercial with a “C” prefix, industrial with an “I” prefix, and

automotive with an “A” prefix. Therefore, commercial devices are indicated as C6, C7,

C8, C8L, or C9L per respective speed grade. Industrial devices are indicated as I7, I8,

or I8L. Automotive devices are indicated as A7.

Cyclone IV E industrial devices I7 are offered with extended operating temperature range.

Chip Altera Cyclone naming rules，Chinese chip Will replace it

PDF

Cyclone® IV GX Field Programmable Gate Array (FPGA) IC 270 6635520 149760 484-BGA

Introduction

The CycloneTM field programmable gate array family is based ona 1.5-V,

0.13-um, alayer copper SRAM process, with densities up to 20,060 logic

elements (LEs) and up to 288 Kbits of RAM. With features like phase-

locked loops (PLLs) for clocking and a dedicated double data rate (DDR)

interface to meet DDR SDRAM and fast cycle RAM (FCRAM) memory

requirements, Cyclone devices are a cost effective solution for data-path

applications. Cyclone devices support various I/O standards, including

LVDS at data rates up to 311 megabits per second (Mbps) and 66-MHz,

32-bit peripheral component interconnect (PCI), for interfacing with and

supporting ASSP and ASIC devices. Altera also offers new low-cost serial

configuration devices to configure Cyclone devices.

Features

■Up to 294,912 RAM bits (36,864 bytes)

■Supports configuration through low-cost serial configuration device

■Support for LVTTL, LVCMOS, SSTL-2, and SSTL-3 I/O standards

■Support for 66-MHz, 32-bit PCI standard

■Low speed (311 Mbps) LVDS 1/O support

■Up to two PLLs per device provide clock multiplication and phase shifting

■Up to eight global clock lines with six clock resources available per

logic array block (LAB) row

■Support for external memory, induding DDR SDRAM (133 MHz),

FCRAM, and single data rate (SDR) SDRAM

■Support for multiple intellectual property (IP) cores, including

Altera" MegaCore functions and Altera Megafunctions Partners

Program (AMPPSM) megafunctions

Chip Altera Cyclone naming rules，Chinese chip Will replace it

PDF

Cyclone® V E Field Programmable Gate Array (FPGA) IC 224 3464192 49000 484-BGA

Summary of Features for Cyclone V Devices

Technology

• TSMC's 28-nm low-power (28LP) process technology

• 1.1 V core voltage

Packaging

• Wirebond low-halogen packages

• Multiple device densities with compatible package footprints for seamless migration between

different device densities

• RoHS-compliant and leaded(1)options

High-performance FPGA fabric

Enhanced 8-input ALM with four registers

Internal memory blocks

• M10K—10-kilobits (Kb) memory blocks with soft error correction code (ECC)

• Memory logic array block (MLAB)—640-bit distributed LUTRAM where you can use up to 25%

of the ALMs as MLAB memory

Embedded Hard IP blocks

Variable-precision DSP

• Native support for up to three signal processing precision levels

(three 9 x 9, two 18 x 18, or one 27 x 27 multiplier) in the same

variable-precision DSP block

• 64-bit accumulator and cascade

• Embedded internal coefficient memory

• Preadder/subtractor for improved efficiency

Memory controller

DDR3, DDR2, and LPDDR2 with 16 and 32 bit ECC support

Embedded transceiver I/O

PCI Express* (PCIe*) Gen2 and Gen1 (x1, x2, or x4) hard IP with

multifunction support, endpoint, and root port

Clock networks

• Up to 550 MHz global clock network

• Global, quadrant, and peripheral clock networks

• Clock networks that are not used can be powered down to reduce dynamic power

Phase-locked loops (PLLs)

• Precision clock synthesis, clock delay compensation, and zero delay buffering (ZDB)

• Integer mode and fractional mode

FPGA General-purpose I/Os (GPIOs)

• 875 megabits per second (Mbps) LVDS receiver and 840 Mbps LVDS transmitter

• 400 MHz/800 Mbps external memory interface

• On-chip termination (OCT)

• 3.3 V support with up to 16 mA drive strength

Low-power high-speed serial interface

• 614 Mbps to 6.144 Gbps integrated transceiver speed

• Transmit pre-emphasis and receiver equalization

• Dynamic partial reconfiguration of individual channels

HPS(Cyclone V SE, SX,and ST devices only)

• Single or dual-core Arm Cortex-A9 MPCore processor-up to 925 MHz maximum frequency with

support for symmetric and asymmetric multiprocessing

• Interface peripherals—10/100/1000 Ethernet media access control (EMAC), USB 2.0

On-The-GO (OTG) controller, quad serial peripheral interface (QSPI) flash controller, NAND

flash controller, Secure Digital/MultiMediaCard (SD/MMC) controller, UART, controller area

network (CAN), serial peripheral interface (SPI), I2C interface, and up to 85 HPS GPIO

interfaces

• System peripherals—general-purpose timers, watchdog timers, direct memory access (DMA)

controller, FPGA configuration manager, and clock and reset managers

• On-chip RAM and boot ROM

• HPS–FPGA bridges—include the FPGA-to-HPS, HPS-to-FPGA, and lightweight HPS-to-FPGA

bridges that allow the FPGA fabric to issue transactions to slaves in the HPS, and vice versa

• FPGA-to-HPS SDRAM controller subsystem—provides a configurable interface to the multiport

front end (MPFE) of the HPS SDRAM controller

• Arm CoreSight™ JTAG debug access port, trace port, and on-chip trace storage

Configuration

• Tamper protection—comprehensive design protection to protect your valuable IP investments

• Enhanced advanced encryption standard (AES) design security features

• CvP

• Dynamic reconfiguration of the FPGA

• Active serial (AS) x1 and x4, passive serial (PS), JTAG, and fast passive parallel (FPP) x8 and

x16 configuration options

• Internal scrubbing (2)

• Partial reconfiguration (3)

How to choose FPGA for your project?

PDF

Cyclone® V E Field Programmable Gate Array (FPGA) IC 336 14251008 301000 672-BGA

Summary of Features for Cyclone V Devices

Technology

• TSMC's 28-nm low-power (28LP) process technology

• 1.1 V core voltage

Packaging

• Wirebond low-halogen packages

• Multiple device densities with compatible package footprints for seamless migration between

different device densities

• RoHS-compliant and leaded(1)options

High-performance FPGA fabric

Enhanced 8-input ALM with four registers

Internal memory blocks

• M10K—10-kilobits (Kb) memory blocks with soft error correction code (ECC)

• Memory logic array block (MLAB)—640-bit distributed LUTRAM where you can use up to 25%

of the ALMs as MLAB memory

Embedded Hard IP blocks

Variable-precision DSP

• Native support for up to three signal processing precision levels

(three 9 x 9, two 18 x 18, or one 27 x 27 multiplier) in the same

variable-precision DSP block

• 64-bit accumulator and cascade

• Embedded internal coefficient memory

• Preadder/subtractor for improved efficiency

Memory controller

DDR3, DDR2, and LPDDR2 with 16 and 32 bit ECC support

Embedded transceiver I/O

PCI Express* (PCIe*) Gen2 and Gen1 (x1, x2, or x4) hard IP with

multifunction support, endpoint, and root port

Clock networks

• Up to 550 MHz global clock network

• Global, quadrant, and peripheral clock networks

• Clock networks that are not used can be powered down to reduce dynamic power

Phase-locked loops (PLLs)

• Precision clock synthesis, clock delay compensation, and zero delay buffering (ZDB)

• Integer mode and fractional mode

FPGA General-purpose I/Os (GPIOs)

• 875 megabits per second (Mbps) LVDS receiver and 840 Mbps LVDS transmitter

• 400 MHz/800 Mbps external memory interface

• On-chip termination (OCT)

• 3.3 V support with up to 16 mA drive strength

Low-power high-speed serial interface

• 614 Mbps to 6.144 Gbps integrated transceiver speed

• Transmit pre-emphasis and receiver equalization

• Dynamic partial reconfiguration of individual channels

HPS(Cyclone V SE, SX,and ST devices only)

• Single or dual-core Arm Cortex-A9 MPCore processor-up to 925 MHz maximum frequency with

support for symmetric and asymmetric multiprocessing

• Interface peripherals—10/100/1000 Ethernet media access control (EMAC), USB 2.0

On-The-GO (OTG) controller, quad serial peripheral interface (QSPI) flash controller, NAND

flash controller, Secure Digital/MultiMediaCard (SD/MMC) controller, UART, controller area

network (CAN), serial peripheral interface (SPI), I2C interface, and up to 85 HPS GPIO

interfaces

• System peripherals—general-purpose timers, watchdog timers, direct memory access (DMA)

controller, FPGA configuration manager, and clock and reset managers

• On-chip RAM and boot ROM

• HPS–FPGA bridges—include the FPGA-to-HPS, HPS-to-FPGA, and lightweight HPS-to-FPGA

bridges that allow the FPGA fabric to issue transactions to slaves in the HPS, and vice versa

• FPGA-to-HPS SDRAM controller subsystem—provides a configurable interface to the multiport

front end (MPFE) of the HPS SDRAM controller

• Arm CoreSight™ JTAG debug access port, trace port, and on-chip trace storage

Configuration

• Tamper protection—comprehensive design protection to protect your valuable IP investments

• Enhanced advanced encryption standard (AES) design security features

• CvP

• Dynamic reconfiguration of the FPGA

• Active serial (AS) x1 and x4, passive serial (PS), JTAG, and fast passive parallel (FPP) x8 and

x16 configuration options

• Internal scrubbing (2)

• Partial reconfiguration (3)

MAX® 10 Field Programmable Gate Array (FPGA) IC 130 387072 8000 169-LFBGA

Intel® MAX® 10 FPGA Device Overview

Intel® MAX® 10 devices are single-chip, non-volatile low-cost programmable logic

devices (PLDs) to integrate the optimal set of system components.

The highlights of the Intel MAX 10 devices include:

• Internally stored dual configuration flash

• User flash memory

• Instant on support

• Integrated analog-to-digital converters (ADCs)

• Single-chip Nios II soft core processor support

Intel MAX 10 devices are the ideal solution for system management, I/O expansion,

communication control planes, industrial, automotive, and consumer applications.

Supporting Feature

Secure on-die flash memory enables device configuration in less than 10 ms

• Single device integrating PLD logic, RAM, flash memory, digital signal processing (DSP), ADC, phase-locked loop (PLL), and I/Os

• Small packages available from 3 mm × 3 mm

• Sleep mode—significant standby power reduction and resumption in less than 1 ms

• Longer battery life—resumption from full power-off in less than 10 ms

Built on TSMC's 55 nm embedded flash process technology

• Intel Quartus® Prime Lite edition (no cost license)

• Platform Designer (Standard) system integration tool

• DSP Builder for Intel FPGAs

• Nios® II Embedded Design Suite (EDS)

How to choose FPGA for your project?

Cyclone® II Field Programmable Gate Array (FPGA) IC 89 119808 4608 144-LQFP

Introduction 

Following the immensely successful first-generation Cyclone® device family, Altera® Cyclone II FPGAs extend the low-cost FPGA density 

range to 68,416 logic elements (LEs) and provide up to 622 usable I/O pins and up to 1.1 Mbits of embedded memory. Cyclone II FPGAs are 

manufactured on 300-mm wafers using TSMC's 90-nm low-k dielectric process to ensure rapid availability and low cost. By minimizing silicon 

area, Cyclone II devices can support complex digital systems on a single chip at a cost that rivals that of ASICs. Unlike other FPGA vendors who 

compromise power consumption and performance for low-cost, Altera’s latest generation of low-cost FPGAs—Cyclone II FPGAs, offer 60% higher 

performance and half the power consumption of competing 90-nm FPGAs. The low cost and optimized feature set of Cyclone II FPGAs make 

them ideal solutions for a wide array of automotive, consumer, communications, video processing, test and measurement, and other 

end-market solutions. Reference designs, system diagrams, and IP, found at www.altera.com, are available to help you rapidly develop complete 

end-market solutions using Cyclone II FPGAs.

Features 

The Cyclone II device family offers the following features:

■ High-density architecture with 4,608 to 68,416 LEs

● M4K embedded memory blocks

● Up to 1.1 Mbits of RAM available without reducing available logic

● 4,096 memory bits per block (4,608 bits per block including 512 parity bits)

● Variable port configurations of ×1, ×2, ×4, ×8, ×9, ×16, ×18, ×32, and ×36

● True dual-port (one read and one write, two reads, or two writes) operation for ×1, ×2, ×4, ×8, ×9, ×16, and ×18 modes

● Byte enables for data input masking during writes

● Up to 260-MHz operation

■ Embedded multipliers

● Up to 150 18- × 18-bit multipliers are each configurable as two independent 9- × 9-bit multipliers with up to 250-MHz 

performance

● Optional input and output registers

■ Advanced I/O support

● High-speed differential I/O standard support, including LVDS, RSDS, mini-LVDS, LVPECL, differential HSTL, and differential 

SSTL 

● Single-ended I/O standard support, including 2.5-V and 1.8-V, SSTL class I and II, 1.8-V and 1.5-V HSTL class I and II, 3.3-V PCI 

and PCI-X 1.0, 3.3-, 2.5-, 1.8-, and 1.5-V LVCMOS, and 3.3-, 2.5-, and 1.8-V LVTTL

● Peripheral Component Interconnect Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 3.0 compliance for 3.3-V 

operation at 33 or 66 MHz for 32- or 64-bit interfaces 

● PCI Express with an external TI PHY and an Altera PCI Express ×1 Megacore® function

● 133-MHz PCI-X 1.0 specification compatibility

● High-speed external memory support, including DDR, DDR2, and SDR SDRAM, and QDRII SRAM supported by drop in 

Altera IP MegaCore functions for ease of use

● Three dedicated registers per I/O element (IOE): one input register, one output register, and one output-enable register

● Programmable bus-hold feature

● Programmable output drive strength feature

● Programmable delays from the pin to the IOE or logic array

● I/O bank grouping for unique VCCIO and/or VREF bank settings

● MultiVolt™ I/O standard support for 1.5-, 1.8-, 2.5-, and 3.3-interfaces

● Hot-socketing operation support

● Tri-state with weak pull-up on I/O pins before and during configuration

● Programmable open-drain outputs

● Series on-chip termination support

■ Flexible clock management circuitry

● Hierarchical clock network for up to 402.5-MHz performance

● Up to four PLLs per device provide clock multiplication and division, phase shifting, programmable duty cycle, and external 

clock outputs, allowing system-level clock management and skew control 

● Up to 16 global clock lines in the global clock network that drive throughout the entire device

■ Device configuration

● Fast serial configuration allows configuration times less than 100 ms

● Decompression feature allows for smaller programming file storage and faster configuration times

● Supports multiple configuration modes: active serial, passive serial, and JTAG-based configuration

● Supports configuration through low-cost serial configuration devices

● Device configuration supports multiple voltages (either 3.3, 2.5, or 1.8 V)

Chip Altera Cyclone naming rules，Chinese chip Will replace it

PDF

Cyclone® V GX Field Programmable Gate Array (FPGA) IC 208 1381376 31500 484-BGA

Summary of Features for Cyclone V Devices

Technology

• TSMC's 28-nm low-power (28LP) process technology

• 1.1 V core voltage

Packaging

• Wirebond low-halogen packages

• Multiple device densities with compatible package footprints for seamless migration between

different device densities

• RoHS-compliant and leaded(1)options

High-performance FPGA fabric

Enhanced 8-input ALM with four registers

Internal memory blocks

• M10K—10-kilobits (Kb) memory blocks with soft error correction code (ECC)

• Memory logic array block (MLAB)—640-bit distributed LUTRAM where you can use up to 25%

of the ALMs as MLAB memory

Embedded Hard IP blocks

Variable-precision DSP

• Native support for up to three signal processing precision levels

(three 9 x 9, two 18 x 18, or one 27 x 27 multiplier) in the same

variable-precision DSP block

• 64-bit accumulator and cascade

• Embedded internal coefficient memory

• Preadder/subtractor for improved efficiency

Memory controller

DDR3, DDR2, and LPDDR2 with 16 and 32 bit ECC support

Embedded transceiver I/O

PCI Express* (PCIe*) Gen2 and Gen1 (x1, x2, or x4) hard IP with

multifunction support, endpoint, and root port

Clock networks

• Up to 550 MHz global clock network

• Global, quadrant, and peripheral clock networks

• Clock networks that are not used can be powered down to reduce dynamic power

Phase-locked loops (PLLs)

• Precision clock synthesis, clock delay compensation, and zero delay buffering (ZDB)

• Integer mode and fractional mode

FPGA General-purpose I/Os (GPIOs)

• 875 megabits per second (Mbps) LVDS receiver and 840 Mbps LVDS transmitter

• 400 MHz/800 Mbps external memory interface

• On-chip termination (OCT)

• 3.3 V support with up to 16 mA drive strength

Low-power high-speed serial interface

• 614 Mbps to 6.144 Gbps integrated transceiver speed

• Transmit pre-emphasis and receiver equalization

• Dynamic partial reconfiguration of individual channels

HPS(Cyclone V SE, SX,and ST devices only)

• Single or dual-core Arm Cortex-A9 MPCore processor-up to 925 MHz maximum frequency with

support for symmetric and asymmetric multiprocessing

• Interface peripherals—10/100/1000 Ethernet media access control (EMAC), USB 2.0

On-The-GO (OTG) controller, quad serial peripheral interface (QSPI) flash controller, NAND

flash controller, Secure Digital/MultiMediaCard (SD/MMC) controller, UART, controller area

network (CAN), serial peripheral interface (SPI), I2C interface, and up to 85 HPS GPIO

interfaces

• System peripherals—general-purpose timers, watchdog timers, direct memory access (DMA)

controller, FPGA configuration manager, and clock and reset managers

• On-chip RAM and boot ROM

• HPS–FPGA bridges—include the FPGA-to-HPS, HPS-to-FPGA, and lightweight HPS-to-FPGA

bridges that allow the FPGA fabric to issue transactions to slaves in the HPS, and vice versa

• FPGA-to-HPS SDRAM controller subsystem—provides a configurable interface to the multiport

front end (MPFE) of the HPS SDRAM controller

• Arm CoreSight™ JTAG debug access port, trace port, and on-chip trace storage

Configuration

• Tamper protection—comprehensive design protection to protect your valuable IP investments

• Enhanced advanced encryption standard (AES) design security features

• CvP

• Dynamic reconfiguration of the FPGA

• Active serial (AS) x1 and x4, passive serial (PS), JTAG, and fast passive parallel (FPP) x8 and

x16 configuration options

• Internal scrubbing (2)

• Partial reconfiguration (3)