NXP USA Inc.

S12Z S12 MagniV Microcontroller IC 16-Bit 32MHz 192KB (192K x 8) FLASH 48-LQFP (7x7)

Introduction

The MC9S12ZVC-Family is a new member of the S12 MagniV product line integrating a battery level

(12V) voltage regulator, supply voltage monitoring, high voltage inputs and a CAN physical interface.It's

primarily targeting at CAN nodes like sensors, switch panels or small actuators. It offers various

low-power modes and wakeup management to address state of the art power consumption requirements.

Some members of theMC9S12ZVC-Family are also offered for high temperature applications requiring

AEC-Q100 Grade 0 (-40℃ to +150C ambient operating temperature range).

The MC9S12ZVC-Family is based on the enhanced performance, linear address space S12Z core and

delivers an optimized solution with the integration of several key system components into a single device,

optimizing system architecture and achieving significant space savings.

Chip-Level Features

On-chip modules available within the family include the following features:

·S12Z CPU core

·Up to 192 Kbyte on-chip flash with ECC

·Up to 2 Kbyte EEPROM with ECC

·Up to 12Kbyte on-chip SRAM with ECC

·Phase locked loop (IPLL) frequency multiplier with internal filter

·1 MHz internal RC oscillator with +/-1.3% accuracy over rated temperature range

·4-20MHz amplitude controlled pierce oscillator

·Internal COP (watchdog) module

·Analog-to-digital converter (ADC) with 12-bit resolution and up to 16 channels available on

external pins

·Two analog comparators (ACMP) with rail-to-rail inputs

·One 8-bit 5V digital-to-analog converter (DAC)

·Up to two serial peripheral interface(SPI) modules

· Up to two serial communication interface (SCI) modules

·SENT Transmitter Interface

·MSCAN(1 Mbit/s,CAN 2.0 A, B software compatible) module

·One on-chip CAN physical layer module

·8-channel timer module (TIM0) with input capture/output compare

·4-channel timer module (TIM1) with input capture/output compare (fast max 64MHz)

·Inter-IC (IIC) module

·4-channel 16-bit Pulse Width Modulation module (PWM0)

·4-channel 16-bit Pulse Width Modulation module (PWM1) (fast max 64MHz)

·On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

·Autonomous periodic interrupt (API), supports cyclic wakeup from Stop mode

·Four pins to support 25 mA drive strength to VSSX

·One pin to support 20 mA drive strength from VDDX (EVDD)

·Two High Voltage Input(HVI) pins

·Supply Vsup monitoring with warning

·On-chip temperature sensor, temperature value can be measured with ADC or can generate a high

temperature interrupt

NXP Electronics components unboxing，humidity card changed color chip can used？

HCS12 HCS12 Microcontroller IC 16-Bit 25MHz 32KB (32K x 8) FLASH 80-QFP (14x14)

Introduction

The MC9S12C-Family / MC9S12GC-Family are 48/52/80 pin Flash-based MCU families, which deliver

the power and flexibility of the 16-bit core to a whole new range of cost and space sensitive, general

purpose industrial and automotive network applications. All MC9S12C-Family / MC9S12GC-Family

members feature standard on-chip peripherals including a 16-bit central processing unit (CPU12), up to

128K bytes of Flash EEPROM, up to 4K bytes of RAM, an asynchronous serial communications interface

(SCI), a serial peripheral interface (SPI), an 8-channel 16-bit timer module (TIM), a 6-channel 8-bit pulse

width modulator (PWM), an 8-channel, 10-bit analog-to-digital converter (ADC).

The MC9S12C128-Family members also feature a CAN 2.0 A, B software compatible module

(MSCAN12).

All MC9S12C-Family / MC9S12GC-Family devices feature full 16-bit data paths throughout. The

inclusion of a PLL circuit allows power consumption and performance to be adjusted to suit operational

requirements. In addition to the I/O ports available in each module, up to 10 dedicated I/O port bits are

available with wake-up capability from stop or wait mode. The devices are available in 48-, 52-, and 80-

pin QFP packages, with the 80-pin version pin compatible to the HCS12 A, B, and D Family derivatives.

Features

• 16-bit HCS12 core:

— HCS12 CPU

– Upward compatible with M68HC11 instruction set

– Interrupt stacking and programmer’s model identical to M68HC11

– Instruction queue

– Enhanced indexed addressing

— MMC (memory map and interface)

— INT (interrupt control)

— BDM (background debug mode)

— DBG12 (enhanced debug12 module, including breakpoints and change-of-flow trace buffer)

— MEBI (multiplexed expansion bus interface) available only in 80-pin package version

• Wake-up interrupt inputs:

— Up to 12 port bits available for wake up interrupt function with digital filtering

• Memory options:

— 16K or 32Kbyte Flash EEPROM (erasable in 512-byte sectors)

64K, 96K, or 128Kbyte Flash EEPROM (erasable in 1024-byte sectors)

— 1K, 2K or 4K Byte RAM

• Analog-to-digital converters:

— One 8-channel module with 10-bit resolution

— External conversion trigger capability

• Available on MC9S12C Family:

— One 1M bit per second, CAN 2.0 A, B software compatible module

— Five receive and three transmit buffers

— Flexible identifier filter programmable as 2 x 32 bit, 4 x 16 bit, or 8 x 8 bit

— Four separate interrupt channels for Rx, Tx, error, and wake-up

— Low-pass filter wake-up function

— Loop-back for self test operation

• Timer module (TIM):

— 8-channel timer

— Each channel configurable as either input capture or output compare

— Simple PWM mode

— Modulo reset of timer counter

— 16-bit pulse accumulator

— External event counting

— Gated time accumulation

• PWM module:

— Programmable period and duty cycle

— 8-bit 6-channel or 16-bit 3-channel

— Separate control for each pulse width and duty cycle

— Center-aligned or left-aligned outputs

— Programmable clock select logic with a wide range of frequencies

— Fast emergency shutdown input

• Serial interfaces:

— One asynchronous serial communications interface (SCI)

— One synchronous serial peripheral interface (SPI)

• CRG (clock reset generator module)

— Windowed COP watchdog

— Real time interrupt

— Clock monitor

— Pierce or low current Colpitts oscillator

— Phase-locked loop clock frequency multiplier

— Limp home mode in absence of external clock

— Low power 0.5MHz to 16MHz crystal oscillator reference clock

• Operating frequency:

— 32MHz equivalent to 16MHz bus speed for single chip

— 32MHz equivalent to 16MHz bus speed in expanded bus modes

— Option of 9S12C Family: 50MHz equivalent to 25MHz bus speed

— All 9S12GC Family members allow a 50MHz operating frequency.

• Internal 2.5V regulator:

— Supports an input voltage range from 2.97V to 5.5V

— Low power mode capability

— Includes low voltage reset (LVR) circuitry

— Includes low voltage interrupt (LVI) circuitry

• 48-pin LQFP, 52-pin LQFP, or 80-pin QFP package:

— Up to 58 I/O lines with 5V input and drive capability (80-pin package)

— Up to 2 dedicated 5V input only lines (IRQ, XIRQ)

— 5V 8 A/D converter inputs and 5V I/O

• Development support:

— Single-wire background debug™ mode (BDM)

— On-chip hardware breakpoints

— Enhanced DBG12 debug features

NXP Electronics components unboxing，humidity card changed color chip can used？

12V1 HCS12 Microcontroller IC 16-Bit 25MHz 128KB (128K x 8) FLASH 100-LQFP (14x14)

Overview

The Freescale Semiconductor MC9S12G family is a feature-rich 16-bit microcontroller product line

focused on low cost, high performance and low pin count for automotive applications. This

family bridges the gap between high-end 8-bit microcontrollers and high-performance 16-bit

microcontrollers, such as the MC9S12XS family. The MC9S12G family is targeted at generic

automotive applications requiring CAN or LIN/SAE J2602 communication and is used in applications

such as body controllers, door modules, occupant detection and lighting modules.

The MC9S12G family uses many of the same features found on the MC9S12XS and MC9S12P

family, including error correction code (ECC) on flash memory, a fast analog-to-digital converter

(ADC) and a frequency modulated phase locked loop (IPLL) that improves the EMC performance. In

order to make using the MC9S12G family easier in your embedded designs, it features an EEPROM

with a small erase sector size.

Features

S12 CPU core, 25 MHz bus and up to 240 KB on-chip flash with ECC

Up to 240 KB on-chip flash with ECC

Up to 4 KB EEPROM with ECC

Up to one multi-scalable controller area network (MSCAN) module (supporting CAN protocol 2.0A/B)

Up to three serial communication interface (SCl) modules supporting LIN communications and up to

three serial peripheral interface (SPI) modules

Up to 12 KB on-chip SRAM

Phase locked loop (IPLL) frequency multiplier with internal filter

Timer module (TIM) supporting up to eight channels that provide a range of 16-bit input capture,output

compare, counter and pulse accumulator functions

Pulse width modulation (PWM) module with up to eight 8-bit channels

Up to 16-channel,12-bit resolution successive approximation analog-to-digital converter (ADC)

Precision fixed voltage reference for ADC conversions

On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

Analog comparator module 8-bit digital-to-analog converter (DAC)