NXP USA Inc.

HCS12X HCS12X Microcontroller IC 16-Bit 40MHz 256KB (256K x 8) FLASH 112-LQFP (20x20)

Introduction

The MC9S12XHY family is an optimized, automotive, 16-bit microcontroller product line that is

specifically designed for entry level instrument clusters. This family also services generic automotive

applications requiring CAN, LCD, Motor driver control or LIN/SAE J2602. Typical examples of these

applications include instrument clusters for automobiles and 2 or 3 wheelers, HVAC displays, general

purpose motor control and body controllers.

The MC9S12XHY family uses many of the same features found on the MC9S12XS family and

MC9S12HY/HA family, including error correction code (ECC) on flash memory, a separate data-flash

module for diagnostic or data storage, a fast analog-to-digital converter (ATD) and a frequency modulated

phase locked loop (IPLL) that improves the EMC performance. The MC9S12XHY family features a 40x4

liquid crystal display (LCD) controller/driver and a motor pulse width modulator (MC) consisting of up to

16 high current outputs. The device is capable of stepper motor stall detection (SSD) via hardware or

software, please contact Freescale sales office for detailed information on software SSD.

The MC9S12XHY family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the

low cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of

Freescale’s existing 8-bit and 16-bit MCU families. Like the MC9S12HY/HA family, the MC9S12XHY

family run 16-bit wide accesses without wait states for all peripherals and memories. The MC9S12XHY

family is available in 112-pin LQFP and 100-pin LQFP package options. In addition to the I/O ports

available in each module, further I/O ports are available with interrupt capability allowing wake-up from

stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• CPU12XV1 CPU core

• Up to 256 Kbyte on-chip flash with ECC

• 8Kbyte data flash with ECC

• Up to 12Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• Two timer modules (TIM0 and TIM1) supporting input/output channels that provide a range of 16-

bit input capture, output compare, counter and pulse accumulator functions

• Pulse width modulation (PWM) module with up to 8 x 8-bit channels

• Up to 12-channel, 10-bit resolution successive approximation analog-to-digital converter (ATD)

• Up to 40x4 LCD driver

• PWM motor controller (MC) with up to 16 high current drivers

• Output slew rate control on Motor driver pad

• One serial peripheral interface (SPI) module

• One Inter-IC bus interface (IIC) module

• Two serial communication interface (SCI) module supporting LIN communications

• Two multi-scalable controller area network (MSCAN) module (supporting CAN protocol 2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)

• Stepper Motor Controller with up to drivers for up to 4 motors

• Four Stepper Stall Detector modules (one for each motor)

• Up to 25 key wakup inputs

NXP Electronics components unboxing，humidity card changed color chip can used？

HCS12X HCS12X Microcontroller IC 16-Bit 40MHz 256KB (256K x 8) FLASH 100-LQFP (14x14)

Introduction

The MC9S12XHY family is an optimized, automotive, 16-bit microcontroller product line that is

specifically designed for entry level instrument clusters. This family also services generic automotive

applications requiring CAN, LCD, Motor driver control or LIN/SAE J2602. Typical examples of these

applications include instrument clusters for automobiles and 2 or 3 wheelers, HVAC displays, general

purpose motor control and body controllers.

The MC9S12XHY family uses many of the same features found on the MC9S12XS family and

MC9S12HY/HA family, including error correction code (ECC) on flash memory, a separate data-flash

module for diagnostic or data storage, a fast analog-to-digital converter (ATD) and a frequency modulated

phase locked loop (IPLL) that improves the EMC performance. The MC9S12XHY family features a 40x4

liquid crystal display (LCD) controller/driver and a motor pulse width modulator (MC) consisting of up to

16 high current outputs. The device is capable of stepper motor stall detection (SSD) via hardware or

software, please contact Freescale sales office for detailed information on software SSD.

The MC9S12XHY family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the

low cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of

Freescale’s existing 8-bit and 16-bit MCU families. Like the MC9S12HY/HA family, the MC9S12XHY

family run 16-bit wide accesses without wait states for all peripherals and memories. The MC9S12XHY

family is available in 112-pin LQFP and 100-pin LQFP package options. In addition to the I/O ports

available in each module, further I/O ports are available with interrupt capability allowing wake-up from

stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• CPU12XV1 CPU core

• Up to 256 Kbyte on-chip flash with ECC

• 8Kbyte data flash with ECC

• Up to 12Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• Two timer modules (TIM0 and TIM1) supporting input/output channels that provide a range of 16-

bit input capture, output compare, counter and pulse accumulator functions

• Pulse width modulation (PWM) module with up to 8 x 8-bit channels

• Up to 12-channel, 10-bit resolution successive approximation analog-to-digital converter (ATD)

• Up to 40x4 LCD driver

• PWM motor controller (MC) with up to 16 high current drivers

• Output slew rate control on Motor driver pad

• One serial peripheral interface (SPI) module

• One Inter-IC bus interface (IIC) module

• Two serial communication interface (SCI) module supporting LIN communications

• Two multi-scalable controller area network (MSCAN) module (supporting CAN protocol 2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)

• Stepper Motor Controller with up to drivers for up to 4 motors

• Four Stepper Stall Detector modules (one for each motor)

• Up to 25 key wakup inputs

NXP Electronics components unboxing，humidity card changed color chip can used？

S12Z S12 MagniV Microcontroller IC 16-Bit 32MHz 64KB (64K x 8) FLASH 32-LQFP (7x7)

Introduction

The MC9S12ZVL-Family is an automotive 16-bit microcontroller family using the180nm NVM+UHV

technology that offers the capability to integrate 40V analog components. This family reuses many

features from the existing S12 portfolio. The particular differentiating features of this family are the

enhanced S12Z core and the integration of “high-voltage”analog modules, including the voltage regulator

(VREG) and a Local Interconnect Network (LIN) physical layer.

The MC9S12ZVL-Family includes error correction code (ECC) on RAM, FLASH and EEPROM for

diagnostic or data storage, a fast analog-to-digital converter (ADC) and a frequency modulated phase

locked loop (IPLL) that improves the EMC performance. The MC9S12ZVL-Family delivers an optimized

solution with the integration of several key system components into a single device, optimizing system

architecture and achieving significant space savings. TheMC9S12ZVL-Family delivers all the advantages

and efficiencies of a 16-bit MCU while retaining the low cost, power consumption, EMC, and code-size

efficieney advantages currently enjoyed by users of existing S12 families. The MC9S12ZVL-Family is

available in 48-pin, 32-pin LQFP and 32-pin QFN-EP. In addition to the I/O ports available in each

module, further I/O ports are available with interrupt capability allowing wake-up from stop or wait

modes.

The MC9S12ZVL-Family is a general-purpose family of devices suitable for a wide range of applications.

The MC9S12ZVL-Family is targeted at generic automotive applications requiring LIN connectivity.

Typical examples of these applications include switch panels and body endpoints for sensors.

Chip-Level Features

On-chip modules available within the family include the following features:

·S12Z CPU core

·128, 96, 64, 32, 16 or 8 KB on-chip flash with ECC

·2048,1024,128 byte EEPROM with ECC

·8192,4096, 1024 or 512 byte on-chip SRAM with ECC

·Phase locked loop (IPLL) frequency multiplier with internal filter

·1 MHz internal RC oscillator with +/-1.3% accuracy over rated temperature range

·4-20MHz amplitude controlled pierce oscillator

·Internal COP (watchdog) module

·analog-to-digital converter (ADC) with 10-bit or 12-bit resolution and up to 10 channels available

on external pins and Vbg (bandgap) result reference

·PGA module with two input channels

·One 8-bit 5V digital-to-analog converter (DAC)

·One analog comparators (ACMP) with rail-to-rail inputs

·MSCAN(1Mbit/s, CAN2.0 A, B software compatible) module

·One serial peripheral interface (SPI) module

·One serial communication interface (SCI) module with interface to internal LIN physical layer

transceiver (with RX connected to a timer channel for frequency calibration purposes, if desired)

·Up to one additional SCI (not connected to LIN physical layer)

·One on-chip LIN physical layer transceiver fully compliant with the LIN 2.2 standard

·6-channel timer module (TIM0) with input capture/output compare

·2-channel timer module (TIM1) with input capture/output compare

·Inter-IC (IIC) module

·8-channel Pulse Width Modulation module (PWM)

·On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

·Autonomous periodic interrupt (API), supports cyclic wakeup from Stop mode

·Pins to support 25mA drive strength to VSSX

·Pin to support 20mA drive strength from VDDX (EVDD)

·High Voltage Input (HVI)

·Supply voltage sense with low battery warning

·On-chip temperature sensor, temperature value can be measured with ADC or can generate a high

temperature warning

· Up to 23 pins can be used as keyboard wake-up interrupt (KWI)

NXP Electronics components unboxing，humidity card changed color chip can used？