NXP USA Inc.

HCS12 HCS12 Microcontroller IC 16-Bit 32MHz 128KB (128K x 8) FLASH 48-QFN-EP (7x7)

MC9S12P128

Covers also MC9S12P-Family

MC9S12P96

MC9S12P64

MC9S12P32

Introduction

The MC9S12P family is an optimized, automotive, 16-bit microcontroller product line focused on lowcost,

high-performance, and low pin-count. This family is intended to bridge between high-end 8-bit

microcontrollers and high-performance 16-bit microcontrollers, such as the MC9S12XS family. The

MC9S12P family is targeted at generic automotive applications requiring CAN or LIN/J2602

communication. Typical examples of these applications include body controllers, occupant detection, door

modules, seat controllers, RKE receivers, smart actuators, lighting modules, and smart junction boxes.

The MC9S12P family uses many of the same features found on the MC9S12XS family, including error

correction code (ECC) on flash memory, a separate data-flash module for diagnostic or data storage, a fast

analog-to-digital converter (ATD) and a frequency modulated phase locked loop (IPLL) that improves the

EMC performance.

The MC9S12P family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the low

cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of

Freescale’s existing 8-bit and 16-bit MCU families. Like the MC9S12XS family, the MC9S12P family run

16-bit wide accesses without wait states for all peripherals and memories. The MC9S12P family is

available in 80-pin QFP, 64-pin LQFP, and 48-pin QFN package options and aims to maximize pin

compatibility with the MC9S12XS family. In addition to the I/O ports available in each module, further

I/O ports are available with interrupt capability allowing wake-up from stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• S12 CPU core

• Up to 128 Kbyte on-chip flash with ECC

• 4 Kbyte data flash with ECC

• Up to 6 Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• 1 MHz internal RC oscillator

• Timer module (TIM) supporting input/output channels that provide a range of 16-bit input capture,

output compare, counter, and pulse accumulator functions

• Pulse width modulation (PWM) module with 6 x 8-bit channels

• 10-channel, 12-bit resolution successive approximation analog-to-digital converter (ATD)

• One serial peripheral interface (SPI) module

• One serial communication interface (SCI) module supporting LIN communications

• One multi-scalable controller area network (MSCAN) module (supporting CAN protocol 2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)

HCS12X HCS12X Microcontroller IC 16-Bit 40MHz 128KB (128K x 8) FLASH 100-LQFP (14x14)

Introduction

The MC9S12XHY family is an optimized, automotive, 16-bit microcontroller product line that is

specifically designed for entry level instrument clusters. This family also services generic automotive

applications requiring CAN, LCD, Motor driver control or LIN/SAE J2602. Typical examples of these

applications include instrument clusters for automobiles and 2 or 3 wheelers, HVAC displays, general

purpose motor control and body controllers.

The MC9S12XHY family uses many of the same features found on the MC9S12XS family and

MC9S12HY/HA family, including error correction code (ECC) on flash memory, a separate data-flash

module for diagnostic or data storage, a fast analog-to-digital converter (ATD) and a frequency modulated

phase locked loop (IPLL) that improves the EMC performance. The MC9S12XHY family features a 40x4

liquid crystal display (LCD) controller/driver and a motor pulse width modulator (MC) consisting of up to

16 high current outputs. The device is capable of stepper motor stall detection (SSD) via hardware or

software, please contact Freescale sales office for detailed information on software SSD.

The MC9S12XHY family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the

low cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of

Freescale’s existing 8-bit and 16-bit MCU families. Like the MC9S12HY/HA family, the MC9S12XHY

family run 16-bit wide accesses without wait states for all peripherals and memories. The MC9S12XHY

family is available in 112-pin LQFP and 100-pin LQFP package options. In addition to the I/O ports

available in each module, further I/O ports are available with interrupt capability allowing wake-up from

stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• CPU12XV1 CPU core

• Up to 256 Kbyte on-chip flash with ECC

• 8Kbyte data flash with ECC

• Up to 12Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• Two timer modules (TIM0 and TIM1) supporting input/output channels that provide a range of 16-

bit input capture, output compare, counter and pulse accumulator functions

• Pulse width modulation (PWM) module with up to 8 x 8-bit channels

• Up to 12-channel, 10-bit resolution successive approximation analog-to-digital converter (ATD)

• Up to 40x4 LCD driver

• PWM motor controller (MC) with up to 16 high current drivers

• Output slew rate control on Motor driver pad

• One serial peripheral interface (SPI) module

• One Inter-IC bus interface (IIC) module

• Two serial communication interface (SCI) module supporting LIN communications

• Two multi-scalable controller area network (MSCAN) module (supporting CAN protocol 2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)

• Stepper Motor Controller with up to drivers for up to 4 motors

• Four Stepper Stall Detector modules (one for each motor)

• Up to 25 key wakup inputs

NXP Electronics components unboxing，humidity card changed color chip can used？

HCS12X HCS12X Microcontroller IC 16-Bit 40MHz 256KB (256K x 8) FLASH 112-LQFP (20x20)

Introduction

The MC9S12XHY family is an optimized, automotive, 16-bit microcontroller product line that is

specifically designed for entry level instrument clusters. This family also services generic automotive

applications requiring CAN, LCD, Motor driver control or LIN/SAE J2602. Typical examples of these

applications include instrument clusters for automobiles and 2 or 3 wheelers, HVAC displays, general

purpose motor control and body controllers.

The MC9S12XHY family uses many of the same features found on the MC9S12XS family and

MC9S12HY/HA family, including error correction code (ECC) on flash memory, a separate data-flash

module for diagnostic or data storage, a fast analog-to-digital converter (ATD) and a frequency modulated

phase locked loop (IPLL) that improves the EMC performance. The MC9S12XHY family features a 40x4

liquid crystal display (LCD) controller/driver and a motor pulse width modulator (MC) consisting of up to

16 high current outputs. The device is capable of stepper motor stall detection (SSD) via hardware or

software, please contact Freescale sales office for detailed information on software SSD.

The MC9S12XHY family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the

low cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of

Freescale’s existing 8-bit and 16-bit MCU families. Like the MC9S12HY/HA family, the MC9S12XHY

family run 16-bit wide accesses without wait states for all peripherals and memories. The MC9S12XHY

family is available in 112-pin LQFP and 100-pin LQFP package options. In addition to the I/O ports

available in each module, further I/O ports are available with interrupt capability allowing wake-up from

stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• CPU12XV1 CPU core

• Up to 256 Kbyte on-chip flash with ECC

• 8Kbyte data flash with ECC

• Up to 12Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• Two timer modules (TIM0 and TIM1) supporting input/output channels that provide a range of 16-

bit input capture, output compare, counter and pulse accumulator functions

• Pulse width modulation (PWM) module with up to 8 x 8-bit channels

• Up to 12-channel, 10-bit resolution successive approximation analog-to-digital converter (ATD)

• Up to 40x4 LCD driver

• PWM motor controller (MC) with up to 16 high current drivers

• Output slew rate control on Motor driver pad

• One serial peripheral interface (SPI) module

• One Inter-IC bus interface (IIC) module

• Two serial communication interface (SCI) module supporting LIN communications

• Two multi-scalable controller area network (MSCAN) module (supporting CAN protocol 2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)

• Stepper Motor Controller with up to drivers for up to 4 motors

• Four Stepper Stall Detector modules (one for each motor)

• Up to 25 key wakup inputs

NXP Electronics components unboxing，humidity card changed color chip can used？