S12Z S12 MagniV Microcontroller IC 16-Bit 32MHz 128KB (128K x 8) FLASH 48-LQFP (7x7)

Introduction

The MC9S12ZVC-Family is a new member of the S12 MagniV product line integrating a battery level

(12V) voltage regulator, supply voltage monitoring, high voltage inputs and a CAN physical interface. It's

primarily targeting at CAN nodes like sensors, switch panels or small actuators. It offers various

low-power modes and wakeup management to address state of the art power consumption requirements.

Some members of the MC9S12ZVC-Family are also offered for high temperature applications requiring

AEC-Q100 Grade 0 (-40℃ to +150C ambient operating temperature range).

The MC9S12ZVC-Family is based on the enhanced performance, linear address space S12Z core and

delivers an optimized solution with the integration of severalkey system components into a single device,

optimizing system architecture and achieving significant space savings.

Chip-Level Features

On-chip modules available within the family include the following features:

·S12Z CPU core

·Up to 192 Kbyte on-chip flash with ECC

·Up to 2 Kbyte EEPROM with ECC

·Up to 12Kbyte on-chip SRAM with ECC

·Phase locked loop (IPLL) frequency multiplier with internal filter

·1 MHz internalRC oscillator with +/-1.3% accuracy over rated temperature range

·4-20MHz amplitude controlled pierce oscillator

·Internal COP (watchdog) module

·Analog-to-digital converter (ADC) with 12-bit resolution and up to 16 channels available on

external pins

·Two analog comparators (ACMP) with rail-to-rail inputs

·One 8-bit 5V digita1-to-analog converter(DAC)

·Up to two serial peripheral interface (SPI) modules

·Up to two serial communication interface(SCI) modules

·SENT Transmitter Interface

·MSCAN(1Mbit/s,CAN 2.0 A, B software compatible) module

·One on-chip CAN physical layer module

·8-channel timer module (TIM0) with input capture/output compare

·4-channel timer module (TIM1) with input capture/output compare (fast max 64MHz)

·Inter-IC (IIC) module

·4-channe1 16-bit Pulse Width Modulation module (PWM0)

·4-channe1 16-bit Pulse Width Modulation module (PWM1) (fast max 64MHz)

·On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

·Autonomous periodic interrupt (API), supports cyclic wakeup from Stop mode

·Four pins to support 25 mA drive strength to VSsx

·One pin to support 20 mA drive strength from VDDX (EVDD)

·Two High Voltage Input (HVI) pins

·Supply Vsup monitoring with warning

·On-chip temperature sensor, temperature value can be measured with ADC or can generate a high

temperature interrupt

NXP Electronics components unboxing，humidity card changed color chip can used？

S12Z S12 MagniV Microcontroller IC 16-Bit 32MHz 64KB (64K x 8) FLASH 48-LQFP (7x7)

Introduction

The MC9S12ZVM-Family is an automotive 16-bit microcontroller family using the NVM + UHV

technology that offers the capability to integrate 40 V analog components. This family reuses many

features from the existing S12/S12X portfolio. The particular differentiating features of this family are the

enhanced S12Z core, the combination of dual-ADC synchronized with PWM generation and the

integration of “high-voltage” analog modules, including the voltage regulator (VREG), Gate Drive Unit

(GDU) and a Local Interconnect Network (LIN) physical layer. These features enable a fully integrated

single chip solution to drive up to 6 external power MOSFETs for BLDC or PMSM motor drive

applications.

The MC9S12ZVM-Family includes error correction code (ECC) on RAM and flash memory, EEPROM

for diagnostic or data storage, a fast analog-to-digital converter (ADC) and a frequency modulated phase

locked loop (IPLL) that improves the EMC performance. The MC9S12ZVM-Family delivers an

optimized solution with the integration of several key system components into a single device, optimizing

system architecture and achieving significant space savings. The MC9S12ZVM-Family delivers all the

advantages and efficiencies of a 16-bit MCU while retaining the low cost, power consumption, EMC, and

code-size efficiency advantages currently enjoyed by users of existing S12(X) families. The

MC9S12ZVM-Family is available in different pin-out options, using the 64-pin LQFP-EP and 48-pin

LQFP-EP packages to accommodate LIN, CAN and external PWM based application interfaces. In

addition to the I/O ports available in each module, further I/O ports are available with interrupt capability

allowing wake-up from stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• S12Z CPU core

• 128, 64, 32 or 16KB on-chip flash with ECC

• 512 or128 byte EEPROM with ECC

• 8, 4 or 2 KB on-chip SRAM with ECC

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 1 MHz internal RC oscillator with +/-1.3% accuracy over rated temperature range

• 4-20MHz amplitude controlled pierce oscillator

• Internal COP (watchdog) module

• 6-channel, 15-bit pulse width modulator with fault protection (PMF) 

• Low side and high side FET pre-drivers for each phase

— Gate drive pre-regulator

— LDO (Low Dropout Voltage Regulator) (typically 11V)

— High side gate supply generated using bootstrap circuit with external diode and capacitor

— Sustaining charge pump with two external capacitors and diodes

— High side drain (HD) monitoring on internal ADC channel using HD/5 voltage

• Two parallel analog-to-digital converters (ADC) with 12-bit resolution and up to 9 channels

available on external pins

• Programmable Trigger Unit (PTU) for synchronization of PMF and ADC

• One serial peripheral interface (SPI) module

• One serial communication interface (SCI) module with interface to internal LIN physical layer

transceiver (with RX connected to a timer channel for frequency calibration purposes, if desired)

• Up to one additional SCI (not connected to LIN physical layer)

• On-chip LIN physical layer transceiver fully compliant with the LIN 2.2 standard

(S12ZVML versions)

• One High Voltage physical interface. (S12ZVM32, S12ZVM16 versions only)

• 4-channel timer module (TIM) with input capture/output compare

• MSCAN (1 Mbit/s, CAN 2.0 A, B software compatible) module

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

— Optional VREG ballast control output to supply an external CAN physical layer

• Two current sense circuits for overcurrent detection or torque measurement

• Autonomous periodic interrupt (API)

• 20mA high-current output for use as Hall sensor supply

• Supply voltage sense with low battery warning

• Chip temperature sensor

NXP Electronics components unboxing，humidity card changed color chip can used？

What are the most common mistakes made when sourcing electronic component? | ICONECHIP

For more product unboxing videos, please click on the link

Relevant Content
TJA1040T/CM	1/1 Transceiver Half CANbus 8-SO	MCIMX6Y2CVM08AB	ARM® Cortex®-A7 Microprocessor IC i.MX6 1 Core, 32-Bit 792MHz 289-MAPBGA (14x14)
LPC1768FBD100K	ARM® Cortex®-M3 LPC17xx Microcontroller IC 32-Bit Single-Core 100MHz 512KB (512K x 8) FLASH 100-LQFP (14x14)	MC9S08PA32AVLD	S08 S08 Microcontroller IC 8-Bit 20MHz 32KB (32K x 8) FLASH 44-LQFP (10x10)
FS32K144HFT0VLLT	ARM® Cortex®-M4F S32K Microcontroller IC 32-Bit Single-Core 80MHz 512KB (512K x 8) FLASH 100-LQFP (14x14)	PN7150B0HN/C11002Y	IC RFID READER 13.56MHZ 40HVQFN
PCA9509DP	Buffer, ReDriver 2 Channel 400kHz 8-TSSOP	CLRC66303HNY	IC RFID READER 13.56MHZ 32HVQFN
TJA1057GT/3J	1/1 Transceiver Half CANbus 8-SO	PCF85063ATL/1	Real Time Clock (RTC) IC Clock/Calendar I²C, 2-Wire Serial 10-XFDFN Exposed Pad
PCF85163T/1	REAL-TIME CLOCK AND CALENDAR	SC16IS752IPW	RS232, RS485 Controller I²C, SPI, UART Interface 28-TSSOP
TJA1050T/CM	1/1 Transceiver Half CANbus 8-SO	PCF8563T/5,518	Real Time Clock (RTC) IC Clock/Calendar I²C, 2-Wire Serial 8-SOIC (0.154", 3.90mm Width)

What are the most common mistakes made when sourcing electronic component? | ICONECHIP

For more product unboxing videos, please click on the link

Relevant Content
TJA1040T/CM	1/1 Transceiver Half CANbus 8-SO	MCIMX6Y2CVM08AB	ARM® Cortex®-A7 Microprocessor IC i.MX6 1 Core, 32-Bit 792MHz 289-MAPBGA (14x14)
LPC1768FBD100K	ARM® Cortex®-M3 LPC17xx Microcontroller IC 32-Bit Single-Core 100MHz 512KB (512K x 8) FLASH 100-LQFP (14x14)	MC9S08PA32AVLD	S08 S08 Microcontroller IC 8-Bit 20MHz 32KB (32K x 8) FLASH 44-LQFP (10x10)
FS32K144HFT0VLLT	ARM® Cortex®-M4F S32K Microcontroller IC 32-Bit Single-Core 80MHz 512KB (512K x 8) FLASH 100-LQFP (14x14)	PN7150B0HN/C11002Y	IC RFID READER 13.56MHZ 40HVQFN
PCA9509DP	Buffer, ReDriver 2 Channel 400kHz 8-TSSOP	CLRC66303HNY	IC RFID READER 13.56MHZ 32HVQFN
TJA1057GT/3J	1/1 Transceiver Half CANbus 8-SO	PCF85063ATL/1	Real Time Clock (RTC) IC Clock/Calendar I²C, 2-Wire Serial 10-XFDFN Exposed Pad
PCF85163T/1	REAL-TIME CLOCK AND CALENDAR	SC16IS752IPW	RS232, RS485 Controller I²C, SPI, UART Interface 28-TSSOP
TJA1050T/CM	1/1 Transceiver Half CANbus 8-SO	PCF8563T/5,518	Real Time Clock (RTC) IC Clock/Calendar I²C, 2-Wire Serial 8-SOIC (0.154", 3.90mm Width)

12V1 HCS12 Microcontroller IC 16-Bit 25MHz 64KB (64K x 8) FLASH 48-LQFP (7x7)

Introduction

The MC9S12G-Family is an optimized, automotive, 16-bit microcontroller product line focused on

low-cost, high-performance, and low pin-count. This family is intended to bridge between high-end 8-bit

microcontrollers and high-performance 16-bit microcontrollers, such as the MC9S12XS-Family. The

MC9S12G-Family is targeted at generic automotive applications requiring CAN or LIN/J2602

communication. Typical examples of these applications include body controllers, occupant detection, door

modules, seat controllers, RKE receivers, smart actuators, lighting modules, and smart junction boxes.

The MC9S12G-Family uses many of the same features found on the MC9S12XS- and MC9S12P-Family,

including error correction code (ECC) on flash memory, a fast analog-to-digital converter (ADC) and a

frequency modulated phase locked loop (IPLL) that improves the EMC performance. 

The MC9S12G-Family is optimized for lower program memory sizes down to 16k. In order to simplify

customer use it features an EEPROM with a small 4 bytes erase sector size.

The MC9S12G-Family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the low

cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of NXP’s

existing 8-bit and 16-bit MCU families. Like the MC9S12XS-Family, the MC9S12G-Family run 16-bit

wide accesses without wait states for all peripherals and memories. The MC9S12G-Family is available in

100-pin LQFP, 64-pin LQFP, 48-pin LQFP/QFN, 32-pin LQFP and 20-pin TSSOP package options and

aims to maximize the amount of functionality especially for the lower pin count packages. In addition to

the I/O ports available in each module, further I/O ports are available with interrupt capability allowing

wake-up from stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• S12 CPU core

• Up to 240 Kbyte on-chip flash with ECC

• Up to 4 Kbyte EEPROM with ECC

• Up to 11 Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• 1 MHz internal RC oscillator

• Timer module (TIM) supporting up to eight channels that provide a range of 16-bit input capture,

output compare, counter, and pulse accumulator functions

• Pulse width modulation (PWM) module with up to eight x 8-bit channels

• Up to 16-channel, 10 or 12-bit resolution successive approximation analog-to-digital converter

(ADC)

• Up to two 8-bit digital-to-analog converters (DAC)

• Up to one 5V analog comparator (ACMP)

• Up to three serial peripheral interface (SPI) modules

• Up to three serial communication interface (SCI) modules supporting LIN communications

• Up to one multi-scalable controller area network (MSCAN) module (supporting CAN protocol

2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)

• Precision fixed voltage reference for ADC conversions

• Optional reference voltage attenuator module to increase ADC accuracy

HCS12 HCS12 Microcontroller IC 16-Bit 32MHz 96KB (96K x 8) FLASH 80-QFP (14x14)

Introduction

The MC9S12P family is an optimized, automotive, 16-bit microcontroller product line focused on lowcost,

high-performance, and low pin-count. This family is intended to bridge between high-end 8-bit

microcontrollers and high-performance 16-bit microcontrollers, such as the MC9S12XS family. The

MC9S12P family is targeted at generic automotive applications requiring CAN or LIN/J2602

communication. Typical examples of these applications include body controllers, occupant detection, door

modules, seat controllers, RKE receivers, smart actuators, lighting modules, and smart junction boxes.

The MC9S12P family uses many of the same features found on the MC9S12XS family, including error

correction code (ECC) on flash memory, a separate data-flash module for diagnostic or data storage, a fast

analog-to-digital converter (ATD) and a frequency modulated phase locked loop (IPLL) that improves the

EMC performance.

The MC9S12P family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the low

cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of

Freescale’s existing 8-bit and 16-bit MCU families. Like the MC9S12XS family, the MC9S12P family run

16-bit wide accesses without wait states for all peripherals and memories. The MC9S12P family is

available in 80-pin QFP, 64-pin LQFP, and 48-pin QFN package options and aims to maximize pin

compatibility with the MC9S12XS family. In addition to the I/O ports available in each module, further

I/O ports are available with interrupt capability allowing wake-up from stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• S12 CPU core

• Up to 128 Kbyte on-chip flash with ECC

• 4 Kbyte data flash with ECC

• Up to 6 Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• 1 MHz internal RC oscillator

• Timer module (TIM) supporting input/output channels that provide a range of 16-bit input capture,

output compare, counter, and pulse accumulator functions

• Pulse width modulation (PWM) module with 6 x 8-bit channels

• 10-channel, 12-bit resolution successive approximation analog-to-digital converter (ATD)

• One serial peripheral interface (SPI) module

• One serial communication interface (SCI) module supporting LIN communications

• One multi-scalable controller area network (MSCAN) module (supporting CAN protocol 2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)