NXP USA Inc.

S12Z S12 MagniV Microcontroller IC 16-Bit 32MHz 192KB (192K x 8) FLASH 48-LQFP (7x7)

Introduction

The MC9S12ZVC-Family is a new member of the S12 MagniV product line integrating a battery level

(12V) voltage regulator, supply voltage monitoring, high voltage inputs and a CAN physical interface. It's

primarily targeting at CAN nodes like sensors, switch panels or small actuators. It offers various

low-power modes and wakeup management to address state of the art power consumption requirements.

Some members of the MC9S12ZVC-Family are also offered for high temperature applications requiring

AEC-Q100 Grade 0 (-40℃ to +150C ambient operating temperature range).

The MC9S12ZVC-Family is based on the enhanced performance, linear address space S12Z core and

delivers an optimized solution with the integration of several key system components into a single device,

optimizing system architecture and achieving significant space savings.

Chip-Level Features

·On-chip modules available within the family include the following features:

·S12Z CPU core

·Up to 192 Kbyte on-chip flash with ECC

·Up to 2 Kbyte EEPROM with ECC

· Up to 12Kbyte on-chip SRAM with ECC

·Phase locked loop (IPLL) frequency multiplier with internal filter

·1MHz internal RC oscillator with +/-1.3% accuracy over rated temperature range

·4-20MHz amplitude controlled pierce oscillator

·Internal COP (watchdog) module

·Analog-to-digital converter (ADC) with 12-bit resolution and up to 16 channels available on

external pins

·Two analog comparators (ACMP) with rail-to-rail inputs

·One 8-bit 5V digital-to-analog converter(DAC)

·Up to two serial peripheral interface (SPI) modules

·Up to two serial communication interface(SCI) modules

·SENT Transmitter Interface

·MSCAN(1 Mbit/s,CAN 2.0 A, B software compatible) module

·One on-chip CAN physical layer module

·8-channel timer module (TIM0) with input capture/output compare

·4-channel timer module (TIM1) with input capture/output compare (fast max 64MHz)

·Inter-IC (IIC) module

·4-channel 16-bit Pulse Width Modulation module (PWM0)

·4-channel 16-bit Pulse Width Modulation module (PWM1) (fast max 64MHz)

·On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

·Autonomous periodic interrupt (API), supports cyclic wakeup from Stop mode

·Four pins to support 25 mA drive strength to VSSX

·One pin to support20 mA drive strength from VDDX (EVDD)

·Two High Voltage Input (HVI) pins

·Supply Vsup monitoring with warning

·On-chip temperature sensor, temperature value can be measured with ADC or can generate a high

temperature interrupt

NXP Electronics components unboxing，humidity card changed color chip can used？

S12Z S12 MagniV Microcontroller IC 16-Bit 32MHz 32KB (32K x 8) FLASH 144-LQFP (20x20)

Introduction

The MC9S12ZVH-Family is an optimized automotive 16-bit microcontroller product line focused on low-

cost, high-performance and application component countreduction. This family integrates the components

of an S12HY or S12XHY-family microcontroller with a CAN Physical interface, a 5V regulator system to

supply the microcontroller and other components. The MC9S12ZVH-Family is targeted at automotive &

motorcycle instrument cluster applications requiring CAN connectivity, stepper motor gauges, and

segment LCD displays.

The MC9S12ZVH-Family features a 4x40 liquid crystal display (LCD) controller/driver and a pulse

width modulated motor controller (MC) consisting of up to 16 high current outputs. The device is capable

of stepper motor stall detection (SSD) via hardware or software, please contact Freescale sales office for

detailed information on software SSD.

The MC9S12ZVH-Family delivers an optimized solution with the integration of several key system

components into a single device, optimizing system architecture and achieving significant PCBspace

savings. The MC9S12ZVH-Family delivers all the advantages and efficiencies of a 16-bit MCU while

retaining the low cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed

by users of Freescale's existing 8-bit and 16-bit MCU families. The MC9S12ZVH-Family also features

the revolutionary S12Z CPU with code size & execution efficiencies even higher than our class leading

S12X CPU. This also provides a linear memory map for flash memory for all members of the family,

eliminating the awkwardness and performance impact of page swapping. In addition to the I/O ports

available in each module, further I/O ports are available with interrupt capability allowing wake-up from

stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

•S12Z CPU core

•128 or 64 KB on-chip flash with ECC

•4 KB EEPROM with ECC

•8 or 4 KB on-chip SRAM with ECC

•Phase locked loop (IPLL) frequency multiplier with internal filter

•1 MHz internal RC oscillator with +/-1.3% accuracy over rated temperature range

•4-20 MHz amplitude controlled pierce oscillator

•32 KHz oscillator forRTC and LCD

•Internal COP(watchdog) module

•LCD driver for segment LCD with 40 frontplanes x 4 backplanes

•Stepper Motor Controller with drivers for up to 4 motors

•Up to 4 Stepper Stall Detector (SSD) modules (one for each motor)

•Real Time Clock (RTC) support the Hour/Minute/Second function and frequency compensation

•One Analog-to-Digital Converters (ADC) with 10-bit resolution and up to 8 channels available on

external pins

•Two Timer module (TIM) supporting input/output channels that provide a range of 16-bit input

capture & output compare (8 channels)

•One Pulse Width Modulation (PWM) modules with up to 8 x 8-bit channels

•Simple Sound Generation (SSG) for monotonic tone generation

•One Inter-Integrated Circuit (IIC) module

•One Serial Peripheral Interface (SPI) module

•Two Serial Communication Interface (SCI) module supporting LIN 1.3, 2.0, 2.1 and SAE J2602

communications

•Up to one on-chip high-speed CAN physical layer transceiver

•One MSCAN (up to 1 Mbp/s, CAN 2.0 A, B compliant) module

•On-chip Voltage Regulator (VREG) for regulation of input supply and all internal voltages

•Optional VREG ballast control output to supply an external or internal CAN physical layer

•Autonomous Periodic Interrupt (API) (combination with cyclic, watchdog)

•Supply voltage sense with low battery warning.

•Chip temperature sensor

NXP Electronics components unboxing，humidity card changed color chip can used？

12V1 HCS12 Microcontroller IC 16-Bit 25MHz 48KB (48K x 8) FLASH 64-LQFP (10x10)

Introduction

The MC9S12G-Family is an optimized, automotive, 16-bit microcontroller product line focused on

low-cost, high-performance, and low pin-count. This family is intended to bridge between high-end 8-bit

microcontrollers and high-performance 16-bit microcontrollers, such as the MC9S12XS-Family. The

MC9S12G-Family is targeted at generic automotive applications requiring CAN or LIN/J2602

communication. Typical examples of these applications include body controllers, occupant detection, door

modules, seat controllers, RKE receivers, smart actuators, lighting modules, and smart junction boxes.

The MC9S12G-Family uses many of the same features found on the MC9S12XS- and MC9S12P-Family,

including error correction code (ECC) on flash memory, a fast analog-to-digital converter (ADC) and a

frequency modulated phase locked loop (IPLL) that improves the EMC performance. 

The MC9S12G-Family is optimized for lower program memory sizes down to 16k. In order to simplify

customer use it features an EEPROM with a small 4 bytes erase sector size.

The MC9S12G-Family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the low

cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of NXP’s

existing 8-bit and 16-bit MCU families. Like the MC9S12XS-Family, the MC9S12G-Family run 16-bit

wide accesses without wait states for all peripherals and memories. The MC9S12G-Family is available in

100-pin LQFP, 64-pin LQFP, 48-pin LQFP/QFN, 32-pin LQFP and 20-pin TSSOP package options and

aims to maximize the amount of functionality especially for the lower pin count packages. In addition to

the I/O ports available in each module, further I/O ports are available with interrupt capability allowing

wake-up from stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• S12 CPU core

• Up to 240 Kbyte on-chip flash with ECC

• Up to 4 Kbyte EEPROM with ECC

• Up to 11 Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• 1 MHz internal RC oscillator

• Timer module (TIM) supporting up to eight channels that provide a range of 16-bit input capture,

output compare, counter, and pulse accumulator functions

• Pulse width modulation (PWM) module with up to eight x 8-bit channels

• Up to 16-channel, 10 or 12-bit resolution successive approximation analog-to-digital converter

(ADC)

• Up to two 8-bit digital-to-analog converters (DAC)

• Up to one 5V analog comparator (ACMP)

• Up to three serial peripheral interface (SPI) modules

• Up to three serial communication interface (SCI) modules supporting LIN communications

• Up to one multi-scalable controller area network (MSCAN) module (supporting CAN protocol

2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)

• Precision fixed voltage reference for ADC conversions

• Optional reference voltage attenuator module to increase ADC accuracy

12V1 HCS12 Microcontroller IC 16-Bit 25MHz 48KB (48K x 8) FLASH 64-LQFP (10x10)

Introduction

The MC9S12G-Family is an optimized, automotive, 16-bit microcontroller product line focused on

low-cost, high-performance, and low pin-count. This family is intended to bridge between high-end 8-bit

microcontrollers and high-performance 16-bit microcontrollers, such as the MC9S12XS-Family. The

MC9S12G-Family is targeted at generic automotive applications requiring CAN or LIN/J2602

communication. Typical examples of these applications include body controllers, occupant detection, door

modules, seat controllers, RKE receivers, smart actuators, lighting modules, and smart junction boxes.

The MC9S12G-Family uses many of the same features found on the MC9S12XS- and MC9S12P-Family,

including error correction code (ECC) on flash memory, a fast analog-to-digital converter (ADC) and a

frequency modulated phase locked loop (IPLL) that improves the EMC performance. 

The MC9S12G-Family is optimized for lower program memory sizes down to 16k. In order to simplify

customer use it features an EEPROM with a small 4 bytes erase sector size.

The MC9S12G-Family deliver all the advantages and efficiencies of a 16-bit MCU while retaining the low

cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of NXP’s

existing 8-bit and 16-bit MCU families. Like the MC9S12XS-Family, the MC9S12G-Family run 16-bit

wide accesses without wait states for all peripherals and memories. The MC9S12G-Family is available in

100-pin LQFP, 64-pin LQFP, 48-pin LQFP/QFN, 32-pin LQFP and 20-pin TSSOP package options and

aims to maximize the amount of functionality especially for the lower pin count packages. In addition to

the I/O ports available in each module, further I/O ports are available with interrupt capability allowing

wake-up from stop or wait modes.

Chip-Level Features

On-chip modules available within the family include the following features:

• S12 CPU core

• Up to 240 Kbyte on-chip flash with ECC

• Up to 4 Kbyte EEPROM with ECC

• Up to 11 Kbyte on-chip SRAM

• Phase locked loop (IPLL) frequency multiplier with internal filter

• 4–16 MHz amplitude controlled Pierce oscillator

• 1 MHz internal RC oscillator

• Timer module (TIM) supporting up to eight channels that provide a range of 16-bit input capture,

output compare, counter, and pulse accumulator functions

• Pulse width modulation (PWM) module with up to eight x 8-bit channels

• Up to 16-channel, 10 or 12-bit resolution successive approximation analog-to-digital converter

(ADC)

• Up to two 8-bit digital-to-analog converters (DAC)

• Up to one 5V analog comparator (ACMP)

• Up to three serial peripheral interface (SPI) modules

• Up to three serial communication interface (SCI) modules supporting LIN communications

• Up to one multi-scalable controller area network (MSCAN) module (supporting CAN protocol

2.0A/B)

• On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

• Autonomous periodic interrupt (API)

• Precision fixed voltage reference for ADC conversions

• Optional reference voltage attenuator module to increase ADC accuracy